Máy phát điện
Yêu cầu báo giá
Tải về Tài liệu sản phẩm
Cat® C175-16 (50 HZ)
Máy phát điện diesel Cat C175-16 có công suất từ 2500 - 3100kVA tại tần số 50Hz đáp ứng mọi yêu cầu quan trọng của khách hàng với các ứng dụng phát điện liên tục và dự phòng. Máy phát điện C175-16 được thiết kế đế đáp ứng yêu cầu tải nhanh theo tiêu chuẩn ISO 8528-5 và mang tải 1 bước 100% tải danh định phù hợp với NFPA 110. Cat C175-16 có cấu hình tiêu thụ nhiên liệu thấp hoặc phát thải thấp.
Giá: Liên hệ 1800 599 990 (Nhánh số 0)
360
| Công suất tối thiểu | 2500 kVA |
| Công suất tối đa | 3100 kVA |
| Tiêu chuẩn khí thải/ Tiêu thụ nhiên liệu | Tiêu thụ nhiên liệu thấp hoặc Phát thải thấp |
| Hiệu điện thế | 380 - 11000V |
| Tần số | 50 Hz |
| Tốc độ | 1500 RPM |
| Cấu hình hoạt động | Dự phòng, Liên tục, Nhiệm vụ quan trọng |
| Mô-đen động cơ | Cat® C175-16 SCAC, 16 xilanh, 4 kỳ làm mát bằng nước |
| Đường kính | 175 mm |
| Hành trình píttông | 220 mm |
| Dung tích xi-lanh | 84,7 l |
| Tỷ số nén | 16:07:01 |
| Kiểu nạp khí | TA |
| Hệ thống nhiên liệu | Common Rail |
| Hệ thống điều khiển | Adem™ A4 |
| Chiều dài tối thiểu | 6137 mm |
| Chiều dài tối đa | 7900 mm |
| Chiều rộng tối thiểu | 2110 mm |
| Chiều rộng tối đa | 2786 mm |
| Chiều cao tối thiểu | 2211 mm |
| Chiều cao tối đa | 3307 mm |
| Khối lượng khô tối thiểu | 19391 kg |
| Khối lượng khô tối đa | 23020 kg |
- Cat generator set packages have been fully prototype tested
- Accepts 100% block load in one step and meets NFPA 110 loading requirements
- Conform to ISO 8528-5 steady state and transient response requirements
- Reliable, rugged, durable design
- Field-proven in thousands of applications worldwide
- Four-stroke-cycle diesel engine combines consistent performance and excellent fuel economy with minimum weight
- Superior motor starting capability minimizes need for oversizing alternator
- Designed to match performance and output characteristics of Cat diesel engines
- Robust Class H insulation
- User-friendly interface and navigation
- Scalable system to meet a wide range of installation requirement
- Expansion modules and site-specific programming for specific customer requirements
- Designed to operate in standard ambient temperatures up to 50°C (122°F)
- Contact Phu Thai Cat for specific ambient and altitude capabilities
- EU Declaration of Conformity
- EU Declaration of Incorporation
- IBC seismic certification
- Eurasian Conformity (EAC)
- Components used in the generator set are selected based on seamless design integration to provide the optimum performance
- The generator set is fully assembled at a Caterpillar facility following our quality guidelines
- Each generator set package is tested before leaving the Caterpillar facility
- Cat product support, including dealer service, parts and warranty covers the entire Cat power system
- Cat dealers have over 1,800 dealer branch stores operating in 200 countries
- Phu Thai Cat provides extensive post-sale support, including maintenance and repair agreements
AIR INLET SYSTEM
- 4 x Single element canister with service indicator(s)
CONTROL PANEL
- EMCP 4.2B
- Volts (L-L & L-N)
- Engine cycle crank
- Power Factor (per phase & average)
- Overcurrent
- Communications
- Emergency stop
- 2 Programmable relay outputs (Form C)
- 6 Programmable digital inputs
- 2 Programmable digital outputs
- Environmental sealed front face.
- DC Volts
- Reverse power
- Programmable Protective Relaying Functions
- High coolant temperature
- Accessory module data link
- Low coolant level
- Over / under frequency
- Amps (per phase & average)
- True RMS AC metering, 3-phase, +/-2% accuracy
- Low coolant temperature
- Reverse Reactive Power
- Controls
- Oil pressure (psi, kPa or bar)
- Lamp test
- Coolant temperature
- Warning / shutdown Indicators
- 4 Programmable relay outputs (Form A)
- Alarm acknowledge
- Generator phase sequence
- 24 Volt DC operation
- Serial annunciator module data link
- Customer data link (Modbus RTU)
- Failure to start (overcrank)
- Auto / start / stop control.
- Low oil pressure
- RPM
- Text alarm / event descriptions.
- Digital Indicators
- Generator mounted - rear facing
- Emergency stop pushbutton
- Engine cool-down timer.
- Operating hours
- Over / under voltage
- Overspeed
- Frequency (Hz)
COOLING SYSTEM
- Radiator group - shipped loose
- SCAC cooling
- Coolant Sensors
- Coolant drain line and valves
- Fan and belt guards
EXHAUST SYSTEM
- Bolted flange, with bellow for each turbo
- Dry Exhaust Manifold
FUEL SYSTEM
- Filters x 3
- Secondary / Tertiary fuel filters
- 10 Micron Spin On Type
- 4 Micron Spin On Type
- Primary fuel filter water / fuel water separator
- Engine mounted filters X3
GENERATOR AND ATTACHMENTS
- 6 Leads
- IEC platinum stator RTDs
- Voltage regulator
- Reactive droop capability
- 3 Phase voltage sensing
- RFI suppression
- Min / max exciter limiter
- exciter diode monitor
- Form Wound
- Permanent magnet
- NEMA Class H insulation
- Class H temperature rise at 40C ambient
- (LV) Busbar connections, top/center mounted, top cable entry
- 3 Phase Brushless
- Salient pole
- 50 Hz models: IEC standard hole pattern
- (MV) Busbar connections, right side extension box, bottom cable entry
- Anti condensation space heater
- Class F temperature rise at 40C ambient
- Right side extension box, bottom cable entry
GOVERNING SYSTEM
- ADEM A4
- Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
LUBE SYSTEM
- Gear type lube oil pump
- Lubricating oil
- Fumes disposal
- Integral lube oil cooler
- Oil drain lines and valve
- Oil filter, filler and dipstick
- Prelube - required with prime, continuous, and standby
MOUNTING SYSTEMS
- Rubber anti-vibration mounts (shipped loose)
- Battery disconnect switch
- Batteries and battery rack w/cables
- Dual 24 volt electric starting motors
- Rails - Engine / generator
SERVICE INSTRUCTIONS
- Two PM inspections
POWER TERMINATION
- Busbar
GENERAL
- Paint - Caterpillar yellow with high gloss black rails & radiator
- Right hand service
- Flywheel and flywheel housing-SAE No. 00
- SAE standard rotation
AIR INLET SYSTEM
- Single element air cleaner
- Dual element air cleaner
- Air inlet adapters
- Air inlet protection
CONTROL PANEL
- EMCP 4.3, EMCP 4.4
- EMCP 4.4 optional harness
- EMCP and MV&HV power connection locations
- Load share module
- EMCP mounting location - LV / MV
- Customer AC-DC connection mounting location - LV/MV
- Load share module / auxiliary plate and auxiliary box (LV)
- Load share governor
- Frame boxes
- Automatically selected ground
- EMCP voltage and current sensing groups
- Raise lower switch
- Speed adjust
- Annunciator modules
- Customer interface options
- Generator temperature monitoring
- Modbus monitoring of packages
- E-Stop
- Interconnect harness
- Generator Harness
COOLING SYSTEM
- Package mounted radiator
- Remote radiators
- Fuel cooler
EXHAUST SYSTEM
- Front housing - Standby or mission critical
- Front housing - Prime or continuous
- Exhaust collectors / Manifold
- Exhaust support group
- Mufflers
- Weld flanges
- Aftercooler drain
CRANKCASE SYSTEMS
- Explosive relief valves
- Crankcase ventilation system
FUEL SYSTEM
- Primary fuel filter
GENERATORS AND ATTACHMENTS
- Low voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
- Medium Voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
- Low Voltage - 1800 and 3000 Frames - 60 Hz, 3 phase, 1800 rpm, FW, PM, No of leads=6, Pitch 0.6667
- Space heater kit
- Thermostat for space heater
- Conversion GP-Top cable entry
- Generator air intake
- Differential current transformers
INSTRUMENTATION
- Pyrometer and thermocouples
LUBE SYSTEM
- Lube oil heater
- Drain group oil pans
- Lubricating oil
- Electric prelube pumps
- Oil filters
MOUNTING
- Rubber anti-vibration mounts
- Spring type linear vibration isolators
- IBC vibration isolators - Shipped loose
POWER CONNECTIONS
- Center post busbars (LV)
- Side / Rear mounted busbars (LV)
- Harnesses (Breaker)
- Cable entry options (LV)
- Enclosures - Control packaging (LV)
- Power connection covers (LV)
- Neutral ground (LV)
- 1800 Frame generators circuit breaker
- Masterpack breakers
- Paralleling circuit breakers
- 1800 Frame generator side / rear mounted busbars (MV)
- Cable entry options (MV)
- Neutral ground (MV)
- Low voltage connection cable
- Masterpack breaker connections
SPECIAL TESTS / REPORTS
- Generator test report
- PGS test report @ 1.0 power factor
- PGS test report @ 0.8 power factor
- Standard genset TVA (Torsional Vibration Analysis) report
- Custom genset TVA report
- Special test charge - Engine only
- Genset fuel consumption test
- Standard engine test charge
- IBC seismic certification
- OSCOSH1 seismic certification
STARTING / CHARGING SYSTEM
- 24 Volt power distribution box
- 24 Volt electric starting motors
- Air starting motor
- Air pressure regulator
- Starter location covers
- 24 Volt battery sets - Dry
- Heavy duty battery sets with rack
- 20 Amp battery chargers
- 35 Amp battery chargers
- 50 Amp battery chargers
- Charging alternators - Dry
- Jacket water heaters
- Jacket water heater wiring groups
GENERAL
- Special paint colors
- Service tools - Engine barring group
- Barring group manual
- Engine barring air powered
- Control GP - Air powered bar group
1800 599 990
Live chat
